* levcap-b.m -- relieved bottom of lever cap
* use 1/2" diam ball end mill
* oriented bottom up, tip at left
* tip is X=0, bottom surface (up) is Z=0
* y=0 is edge near operator (eventual right)
Rapid      Z 0.1
Rapid      Y -0.26
* This is about .020 cut per pass in bronze
* The following was generated by program levcap-relief.prl
* X and Z coordinates to cut a curved relief
* in the bottom of a lever cap, using 1/2" ball end mill
* Refer to dwg. levercap.vlm
Rapid      X 0.1584 Z -0.0280
Call 1
Rapid      X 0.1799 Z -0.0380
Call 1
Rapid      X 0.2017 Z -0.0474
Call 1
Rapid      X 0.2237 Z -0.0564
Call 1
Rapid      X 0.2459 Z -0.0647
Call 1
Rapid      X 0.2684 Z -0.0725
Call 1
Rapid      X 0.2910 Z -0.0798
Call 1
Rapid      X 0.3138 Z -0.0865
Call 1
Rapid      X 0.3367 Z -0.0926
Call 1
Rapid      X 0.3598 Z -0.0981
Call 1
Rapid      X 0.3830 Z -0.1031
Call 1
Rapid      X 0.4064 Z -0.1075
Call 1
Rapid      X 0.4298 Z -0.1113
Call 1
Rapid      X 0.4534 Z -0.1145
Call 1
Rapid      X 0.4770 Z -0.1172
Call 1
Rapid      X 0.5006 Z -0.1192
Call 1
Rapid      X 0.5243 Z -0.1207
Call 1
Rapid      X 0.5481 Z -0.1216
Call 1
Rapid      X 0.5718 Z -0.1219
Call 1
Rapid      X 0.5955 Z -0.1216
Call 1
Rapid      X 0.6193 Z -0.1207
Call 1
Rapid      X 0.6430 Z -0.1192
Call 1
Rapid      X 0.6666 Z -0.1172
Call 1
Rapid      X 0.6902 Z -0.1145
Call 1
Rapid      X 0.7138 Z -0.1113
Call 1
Rapid      X 0.7372 Z -0.1075
Call 1
Rapid      X 0.7606 Z -0.1031
Call 1
Rapid      X 0.7838 Z -0.0981
Call 1
Rapid      X 0.8069 Z -0.0926
Call 1
Rapid      X 0.8298 Z -0.0865
Call 1
Rapid      X 0.8526 Z -0.0798
Call 1
Rapid      X 0.8752 Z -0.0725
Call 1
Rapid      X 0.8977 Z -0.0647
Call 1
Rapid      X 0.9199 Z -0.0564
Call 1
Rapid      X 0.9419 Z -0.0474
Call 1
Rapid      X 0.9637 Z -0.0380
Call 1
Rapid      X 0.9852 Z -0.0280
Call 1
* End of output produced by levcap-relief.prl

*
Rapid      Z 0.1
EndMain
*
Sub 1
Line       Y 2.26 Feed 4.0
Rapid      Z 0.1
Rapid      Y -0.26
EndSub

* levcap-h.m - hollow in back of lever cap
* Yehle infill plane
* Oriented bottom up, tip at left
* tip is X=0, bottom surface (up) is Z=0
* y=0 is edge near operator (eventual right)
* Tool is 3/8" end mill w/ corner radius
Rapid      Z 0.1
Rapid      X 1.5206 Y 0.6824
Line       Z -0.04 Feed 1.0
Call 1
Line       Z -0.08 Feed 1.0
Call 1
Line       Z -0.12 Feed 1.0
Call 1
Line       Z -0.16 Feed 1.0
Call 1
Line       Z -0.20 Feed 1.0
Call 1
Line       Z -0.24 Feed 1.0
Call 1
Line       Z -0.28 Feed 1.0
Call 1
Line       Z -0.32 Feed 1.0
Call 1
Line       Z -0.36 Feed 1.0
Call 1
Line       Z -0.40 Feed 1.0
Call 1
* Take down the remaining pillar at center
Rapid      Z 0.1
Rapid      X 1.75 Y 1
Line       Z -0.4 Feed 3.0
Rapid      Z 0.1
EndMain
*
Sub 1
* Entry/Exit: X=1.5206 Y=.6824 Z=plunged
Line       Y 1.3976 Feed 6.0
Arc Ccw    X 2.0877 Y 1.1004 Radius 1.5054
Line       Y 0.9796
Arc Ccw    X 1.5206 Y 0.6824 Radius 1.5054
EndSub